铲车的动力性能基本都要靠油来提供.而装油的柴油机一旦漏油该怎么办呢?这里小编来给大家解析下铲车配件柴油机漏油的种情况及处理措施.

1、喷油嘴回油:喷油嘴是个精密部件.如果柴油机使用不清洁柴油或机器使用日久,就会因喷油嘴磨损而回油.但因更换喷油嘴花钱多,不经济,为避免回油漏掉,可以通过回油管将油引回油箱,或引入柴油过滤器.如果回油管损坏,可用一截塑料管,将油引入自备的容器,经过滤后再倒回油箱.

2、输油部分漏油:可分别情况作适当处理:输油管空心螺丝的垫圈不平,可将垫圈卸下,磨平再垫上,如还不能解决问题,可更换新垫圈,或用较厚的软塑料材料剪成垫圈换上;塑料输油管与金属接头处漏油,多半是塑料输油管硬化或破裂造成,可剪去硬化、破裂部分,然后用热水烫软,趁热装在金属接头上,再用金属丝捆牢;金属输油管破裂漏油,可将破裂处用铜焊焊好.此外,为防止输油管破裂,在安装输油管时,弯度应适宜,不要硬扳着安装,管身不要与机身接触,避免磨坏.

3、气门室罩漏油:气门室罩在安装时,如紧固力过大,就易使其变形漏油.这时,可将漏油的气门室罩卸下来,用木棒小心地捶击整形,使其接触面恢复平整,然后,再垫上垫片,安装好即可.